0
 
You must Register and/or Login to save a shopping cart
You have 0 Items in your Cart Sub Total: $ 0.00
Providing Quality Parts to the Land Cruiser Community Since 1983
California Proposition 65 Notice
WARNING: Operating, servicing and maintaining a passenger vehicle or off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, cadmium and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle. For more information go to www.P65Warnings.ca.gov/passenger-vehicle.
Monthly Specials
FJ55 Tailglass Wthrstrp
Starting at: $ 340.00

Search
<<  Browse Catalog  >>


...Featured Product...

Page 291 Land Cruiser Ring and Pinions

<<< >>> Limited Slips & Lockers Ring & Pinions
Aftermarket Ring & Pinions Sets & Kits

Ring & Pinion Kits

Ring & Pinion Kits
SOR Photo
PHOTO SHOWN ABOVE
DOES NOT DEPICT ALL
YEARS AND MODELS
(click for large picture)
What Gear Ratio Do You Need:
3:70 Ring &
Pinion Kit
4:11 Ring &
Pinion Kit
4:56 Ring &
Pinion Kit
4:88 Ring &
Pinion Kit
5:29 Ring &
Pinion Kit
3:70
Installation
Kit
4:11
Installation
Kit
4:56
Installation
Kit
4:88
Installation
Kit
5:29
Installation
Kit

This job requires pulling axles out, now is a good time to replace seals, bearings and gaskets for the outer axle assemblies. For front axle assemblies see page see page 080. For rear semi-float rear axle assembly parts, see page 088. For full-float rear axle assembly parts, see page 089. And don't forget to purchase a Differential Service Manual, part #223-26.

SOR Photo
SOR offers complete Ring and Pinion Kits. Other companies offer ring and pinion gear sets but SOR offers complete assembly kits. Ratios offered include 3:704.11, 4.56, 4:88, and 5:29 to fit in vehicles from 1958 to 1998. These kits come with all hard parts required for installation into your year differential. Please note not all kits come with ring gear bolts and nuts. If your original year vehicle's differential has re-useable hardware, the kit will not include the nuts and bolts. Please inspect your assembly to determine if you need this hardware. Order the Ring & Pinion Gear Kit AND the Installation kit for your year and model and it will come with all the necessary parts you will need to do the installation, assuming the axle assembly is all original. Insure that your rebuild last. For procedures and specifications, purchase the Differential Repair Manual, part #223-26.
 
Silicone gasket sealer is provided in the installation kit, Specter however recommends you use the original factory differential gaskets, order #090-40 and #090-41 separately. Ring and Pinion Kits must be ordered IN ADDITION to the Installation Kits (#291-9500, #291-9511-F, and #291-9511-R). Professional Installation Recommended
3:70 Ratio Ring and Pinion Gear Kit
Buy
Quantity
Part Number
Description
Price
*In Stock
291-9010
3:70 RING AND PINION KIT -
Fits 1958-1967 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
On Sale - Everyone gets the Discounted Price on this part.
555.00
291-9011
3:70 RING AND PINION KIT -**Special Order NO Return
Fits 1968-5/72 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
On Sale - Everyone gets the Discounted Price on this part.
Special Order NO Return
560.00
291-9012
3:70 RING AND PINION KIT -
Fits 5/72-1/74 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
On Sale - Everyone gets the Discounted Price on this part.
450.00
291-9013
3:70 RING AND PINION KIT -
Fits 1/74-1/78 - Comes with all the hard parts required for installation into your differential - Requires Installation Kit (#291-9500), order separately
On Sale - Everyone gets the Discounted Price on this part.
499.35
291-9014
3:70 RING AND PINION KIT -
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
On Sale - Everyone gets the Discounted Price on this part.
366.00
3:70 Installation Kit
Buy
Quantity
Part Number
Description
Price
In Stock
Picture
(Click to Enlarge & Close)
291-9500
FRONT & REAR RING AND PINION INSTALLATION KIT-
Fits 1958-1/90 front Ring and Pinion & 1958-11/89 rear Ring and Pinion. This kit contains the correct side bearings for lockers and limited slip units using 45mm ID side bearings (check your new locker requirements). This kit is designed for the updated ring and pinion that uses a crush sleeve. If you have a shim type ring and pinion you must then also purchase part number 090-26A (qty 1). Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 103.20 Click here for info about joining Club SOR
129.00
090-40A
DIFFERENTIAL INSPECTION COVER GASKET -
Fits 1958-1/95
Club Price with 20% Discount is $ 6.40 Click here for info about joining Club SOR
8.00
090-41A
6.48
4:11 Ratio Ring and Pinion Gear Kit
Buy
Quantity
Part Number
Description
Price
*In Stock
291-9020
4:11 RING AND PINION KIT -
Fits 1958-1967 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 294.40 Click here for info about joining Club SOR
368.00
291-9021
4:11 RING AND PINION KIT -
Fits 1968-5/72 - Comes with all the hard parts required for installation into your differential - Requires Installation Kit (#291-9500), order separately - This is a Crush Sleeve style kit.
Club Price with 20% Discount is $ 316.00 Click here for info about joining Club SOR
395.00
291-9022
4:11 RING AND PINION KIT -
Fits 5/72-1/74 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 212.00 Click here for info about joining Club SOR
265.00
291-9023
4:11 RING AND PINION KIT -
Fits 1/74-1/78 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 200.00 Click here for info about joining Club SOR
250.00
291-9024
4:11 RING AND PINION KIT -
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
Club Price with 20% Discount is $ 192.00 Click here for info about joining Club SOR
240.00
4:11 Installation Kit
Buy
Quantity
Part Number
Description
Price
In Stock
Picture
(Click to Enlarge & Close)
291-9500
FRONT & REAR RING AND PINION INSTALLATION KIT-
Fits 1958-1/90 front Ring and Pinion & 1958-11/89 rear Ring and Pinion. This kit contains the correct side bearings for lockers and limited slip units using 45mm ID side bearings (check your new locker requirements). This kit is designed for the updated ring and pinion that uses a crush sleeve. If you have a shim type ring and pinion you must then also purchase part number 090-26A (qty 1). Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 103.20 Click here for info about joining Club SOR
129.00
090-40A
DIFFERENTIAL INSPECTION COVER GASKET -
Fits 1958-1/95
Club Price with 20% Discount is $ 6.40 Click here for info about joining Club SOR
8.00
090-41A
6.48
4:56 Ratio Ring and Pinion Gear Kit
Buy
Quantity
Part Number
Description
Price
*In Stock
291-9030
4:56 RING AND PINION KIT -**Special Order NO Return
Fits 1958-1967 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 276.00 Click here for info about joining Club SOR
Special Order NO Return
345.00
291-9031
4:56 RING AND PINION KIT -**Special Order NO Return
Fits 1968-5/72 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 296.00 Click here for info about joining Club SOR
Special Order NO Return
370.00
291-9032
4:56 RING AND PINION KIT -**Special Order NO Return
Fits 5/72-1/74 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 296.00 Click here for info about joining Club SOR
Special Order NO Return
370.00
291-9033
4:56 RING AND PINION KIT -
Fits 1/74-1/78 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 314.40 Click here for info about joining Club SOR
393.00
291-9034
4:56 RING AND PINION KIT-
4:56 Ratio-Fits 1/78-1/90-Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
Club Price with 20% Discount is $ 208.00 Click here for info about joining Club SOR
260.00
4:56 Installation Kit
Buy
Quantity
Part Number
Description
Price
In Stock
Picture
(Click to Enlarge & Close)
291-9500
FRONT & REAR RING AND PINION INSTALLATION KIT-
Fits 1958-1/90 front Ring and Pinion & 1958-11/89 rear Ring and Pinion. This kit contains the correct side bearings for lockers and limited slip units using 45mm ID side bearings (check your new locker requirements). This kit is designed for the updated ring and pinion that uses a crush sleeve. If you have a shim type ring and pinion you must then also purchase part number 090-26A (qty 1). Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 103.20 Click here for info about joining Club SOR
129.00
090-40A
DIFFERENTIAL INSPECTION COVER GASKET -
Fits 1958-1/95
Club Price with 20% Discount is $ 6.40 Click here for info about joining Club SOR
8.00
090-41A
6.48
4:88 Ratio Ring and Pinion Gear Kit
Buy
Quantity
Part Number
Description
Price
*In Stock
291-9040
4:88 RING AND PINION KIT -
Fits 1958-1967 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
On Sale - Everyone gets the Discounted Price on this part.
350.00
291-9041
4:88 RING AND PINION KIT -
Fits 1968-5/72 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 280.00 Click here for info about joining Club SOR
350.00
291-9042
4:88 RING AND PINION KIT -
Fits 5/72-1/74 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 220.00 Click here for info about joining Club SOR
275.00
291-9043
4:88 RING AND PINION KIT -
Fits 1/74-1/78 -Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 220.00 Click here for info about joining Club SOR
275.00
291-9044
4:88 RING AND PINION KIT -
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
Club Price with 20% Discount is $ 208.00 Click here for info about joining Club SOR
260.00
291-9045-F
4:88 RING AND PINION KIT -**Special Order NO Return
Fits 1/90-1/98 FJ80 Front - Comes with Ring and Pinion only - Requires installation kit (#291-9511-F), order separately
Club Price with 20% Discount is $ 281.26 Click here for info about joining Club SOR
Special Order NO Return
351.58
291-9045-R
4:88 RING AND PINION KIT -
Fits 1/90-1/98 FJ80 Rear - Comes with Ring and Pinion only – Requires installation kit (#291-9511-R), order separately
Club Price with 20% Discount is $ 208.00 Click here for info about joining Club SOR
260.00
4:88 Installation Kits
Buy
Quantity
Part Number
Description
Price
In Stock
Picture
(Click to Enlarge & Close)
291-9500
FRONT & REAR RING AND PINION INSTALLATION KIT-
Fits 1958-1/90 front Ring and Pinion & 1958-11/89 rear Ring and Pinion. This kit contains the correct side bearings for lockers and limited slip units using 45mm ID side bearings (check your new locker requirements). This kit is designed for the updated ring and pinion that uses a crush sleeve. If you have a shim type ring and pinion you must then also purchase part number 090-26A (qty 1). Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 103.20 Click here for info about joining Club SOR
129.00
291-9511-F
FRONT RING AND PINION INSTALLATION KIT-
Fits 1/90-1/98 front Ring and Pinion WITHOUT Diff Lock -Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 231.20 Click here for info about joining Club SOR
289.00
291-9511-R
REAR RING AND PINION INSTALLATION KIT-
Fits 11/89-1/98 rear Ring and Pinion WITHOUT Diff Lock -Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 171.20 Click here for info about joining Club SOR
214.00
090-40A
DIFFERENTIAL INSPECTION COVER GASKET -
Fits 1958-1/95
Club Price with 20% Discount is $ 6.40 Click here for info about joining Club SOR
8.00
090-41A
6.48
5:29 Ratio Ring and Pinion Gear Kit
Buy
Quantity
Part Number
Description
Price
*In Stock
291-9050
5:29 RING AND PINION KIT -
Fits 1958-1967 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 343.66 Click here for info about joining Club SOR
429.57
291-9051
5:29 RING AND PINION KIT -
Fits 1968-5/72 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 343.66 Click here for info about joining Club SOR
429.57
291-9052
5:29 RING AND PINION KIT -
Fits 5/72-1/74 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 308.00 Click here for info about joining Club SOR
385.00
291-9053
5:29 RING AND PINION KIT -
Fits 1/74-1/78 - Comes with all the hard parts required for installation into your differential-Requires Installation Kit (#291-9500), order separately
Club Price with 20% Discount is $ 280.00 Click here for info about joining Club SOR
350.00
291-9054
5:29 RING AND PINION KIT -**Special Order NO Return
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
On Sale - Everyone gets the Discounted Price on this part.
Special Order NO Return
255.43
291-9055-F
5:29 RING AND PINION KIT -
Fits 1/90-1/98 FJ80 Front - Comes with Ring and Pinion only - Requires installation kit (#291-9511-F), order separately
On Sale - Everyone gets the Discounted Price on this part.
234.57
291-9055-R
5:29 RING AND PINION KIT -**Special Order NO Return
Fits 1/90-1/98 FJ80 Rear - Comes with Ring and Pinion only - Requires installation kit (#291-9511-R), order separately
On Sale - Everyone gets the Discounted Price on this part.
Special Order NO Return
255.43
5:29 Installation Kits
Buy
Quantity
Part Number
Description
Price
In Stock
Picture
(Click to Enlarge & Close)
291-9500
FRONT & REAR RING AND PINION INSTALLATION KIT-
Fits 1958-1/90 front Ring and Pinion & 1958-11/89 rear Ring and Pinion. This kit contains the correct side bearings for lockers and limited slip units using 45mm ID side bearings (check your new locker requirements). This kit is designed for the updated ring and pinion that uses a crush sleeve. If you have a shim type ring and pinion you must then also purchase part number 090-26A (qty 1). Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 103.20 Click here for info about joining Club SOR
129.00
291-9511-F
FRONT RING AND PINION INSTALLATION KIT-
Fits 1/90-1/98 front Ring and Pinion WITHOUT Diff Lock -Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 231.20 Click here for info about joining Club SOR
289.00
291-9511-R
REAR RING AND PINION INSTALLATION KIT-
Fits 11/89-1/98 rear Ring and Pinion WITHOUT Diff Lock -Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 171.20 Click here for info about joining Club SOR
214.00
090-40A
DIFFERENTIAL INSPECTION COVER GASKET -
Fits 1958-1/95
Club Price with 20% Discount is $ 6.40 Click here for info about joining Club SOR
8.00
090-41A
6.48
Differential Repair Manual
SOR Photo
(click for large picture)

This manual has detailed instructions for setting up both the shim type and crush sleeve type ring and pinion assemblies.

Buy
Quantity
Part Number
Description
Price
*In Stock
223-26
DIFFERENTIAL REPAIR MANUAL -
Fits 1958-1/90 - Reprint. Covers front and rear differentials. This manual has detailed instructions for setting up both the shim type and crush sleeve type ring and pinion assemblies. 54 pages. This information is already in the Chassis and Body Manual.
On Sale - Everyone gets the Discounted Price on this part.
12.75

Ring & Pinion Sets

Ring & Pinon
 
Ring & Pinion Sets
SOR Photo
(click for large picture)

SOR has noticed that other vendors selling differential gears list only the Ring and Pinion gear price. For those of you who are price comparing here are prices of just the Ring and Pinion gear. Please note all the gear sets available for the Land Cruiser are crush sleeve type requiring a fine splined drive flange. This means there are more parts required to use these gears than just the ring and pinion. For those of you who want to know the price of all the parts needed to install these new Ring and Pinion sets, scroll down the page to the COMPLETE Ring and Pinion Kits and the Installation Kits.

Buy
Quantity
Part Number
Description
Price
*In Stock
291-9024
4:11 RING AND PINION KIT -
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
Club Price with 20% Discount is $ 192.00 Click here for info about joining Club SOR
240.00
291-9034
4:56 RING AND PINION KIT-
4:56 Ratio-Fits 1/78-1/90-Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
Club Price with 20% Discount is $ 208.00 Click here for info about joining Club SOR
260.00
291-9044
4:88 RING AND PINION KIT -
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
Club Price with 20% Discount is $ 208.00 Click here for info about joining Club SOR
260.00
291-9045-R
4:88 RING AND PINION KIT -
Fits 1/90-1/98 FJ80 Rear - Comes with Ring and Pinion only – Requires installation kit (#291-9511-R), order separately
Club Price with 20% Discount is $ 208.00 Click here for info about joining Club SOR
260.00
291-9054
5:29 RING AND PINION KIT -**Special Order NO Return
Fits 1/78-1/90 - Comes with the ring and pinion only-Requires Installation Kit (#291-9500 or #291-9511-R depending on application), order separately
On Sale - Everyone gets the Discounted Price on this part.
Special Order NO Return
255.43
291-9500
FRONT & REAR RING AND PINION INSTALLATION KIT-
Fits 1958-1/90 front Ring and Pinion & 1958-11/89 rear Ring and Pinion. This kit contains the correct side bearings for lockers and limited slip units using 45mm ID side bearings (check your new locker requirements). This kit is designed for the updated ring and pinion that uses a crush sleeve. If you have a shim type ring and pinion you must then also purchase part number 090-26A (qty 1). Even though silicone is provided in the installation kit, Specter recommends you use the original factory differential gaskets (#090-40 & #090-41), order separately
Club Price with 20% Discount is $ 103.20 Click here for info about joining Club SOR
129.00
<< Top of Page >>

Specter Off-Road, Inc.

World's Largest Supplier of Land Cruiser Parts & Accessories. Providing Quality Parts Since 1983
© Copyright 1996 - Specter Off-Road, Inc. All rights reserved. Specter Off-Road, Inc. is not affiliated with Toyota Motor Sales or Toyota Motor Corporation.
TT=00:00:00 249 107.20.120.65

Contact SOR
Mailing Address: 21600 Nordhoff St. Chatsworth, California 91311 USA
Customer Entrance: 21601 Osborne St. (We're a city block long)
Phone: (818) 882-1238, Fax: (818) 882-7144, Email: sor@sor.com
Hours: Monday-Friday 8:00AM-6PM PST,
Closed Saturday & Sunday