0
 
You must Register and/or Login to save a shopping cart
You have 0 Items in your Cart Sub Total: $ 0.00
Providing Quality Parts to the Land Cruiser Community Since 1983
California Proposition 65 Notice
WARNING: Operating, servicing and maintaining a passenger vehicle or off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, cadmium and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle. For more information go to www.P65Warnings.ca.gov/passenger-vehicle.
Monthly Specials
FJ55 Tailglass Wthrstrp
Starting at: $ 340.00

Search
<<  Browse Catalog  >>


...Featured Product...

Page 090 Land Cruiser Locking Differential

<<< >>> Open Differentials Factory Locking Differentials
Factory Locking Differentials

1/90 - 1/98 80 Series with Factory Locker

Click the NUMBERS for part listings
Click on the BLUE HIGHLIGHTED NUMBERS in the line drawings to display a COMPLETE part listing of that part number.
 
#090-15-Kit
Rear Factory Locker

#090-15-Kit

Differential Lock – 10/85-1/90 60, 62 and 70 Series

Click the NUMBERS for part listings
Click on the BLUE HIGHLIGHTED NUMBERS in the line drawings to display a COMPLETE part listing of that part number.
Front
Rear

Differential Lock – 1/90-1/98 80 Series

Click the NUMBERS for part listings
Click on the BLUE HIGHLIGHTED NUMBERS in the line drawings to display a COMPLETE part listing of that part number.
Front
Rear
 
Service Tip: Differential overhaul

Specter recommends that you not attempt any work on the differential without the aid of the Factory Chassis & Body Repair Manual (see page 221). Check #13 Shaft, #18 Gears, #19 Washers for scoring. When reinstalling flange #31 use grease so you don't scar or rip the rubber lip of #29 pinion seal. If #29 Pinion seal is leaking there is a possibility the #31 Flange has a slight groove where the seal rides or that #26 Shims have spun and have become thinner. This also causes play in the #31 flange. If you were just to tighten the nut, improper bearing pre-load #20 to #27 will occur and cause bearing failure. Check #27 Bearing for scoring on race & rollers. Also check #26 shims for spinning. Replace parts as needed. Always replace #29 Pinion Seal on replacement of any parts. Torque spec on #33 nut is 160 ft/lbs.

Tech Note
Tech Note: Differential overhaul
Small Fill Plugs
17mm
Large Fill Plugs
24mm
#090-33A Castle Nut Fits 1958-8/69
26mm
#090-33B Stake Nut Fits 8/69-1/78
27mm
#090-33C Stake Nut Fits 1/78-4/85
30mm
#090-33D Stake Nut Fits 4/85-1/98
30mm
#090-33E-R Stake Nut (Rear) Fits 1/98 & Later
30mm
<< Top of Page >>

Specter Off-Road, Inc.

World's Largest Supplier of Land Cruiser Parts & Accessories. Providing Quality Parts Since 1983
© Copyright 1996 - Specter Off-Road, Inc. All rights reserved. Specter Off-Road, Inc. is not affiliated with Toyota Motor Sales or Toyota Motor Corporation.
TT=00:00:00 144 54.224.18.114

Contact SOR
Mailing Address: 21600 Nordhoff St. Chatsworth, California 91311 USA
Customer Entrance: 21601 Osborne St. (We're a city block long)
Phone: (818) 882-1238, Fax: (818) 882-7144, Email: sor@sor.com
Hours: Monday-Friday 8:00AM-6PM PST,
Closed Saturday & Sunday