
SOR 2 Piece Silver Ceramic Coated Headers are built exclusively for Specter Off-Road in the USA. These top quality headers are designed to fit right! Made from Ceramic Coated Steel to resist corrosion. Requires SOR Stainless Steel Header Pipe for installation see part #324-410. Complete your exhaust system head to tail by including the SOR Muffler and Tail Pipe Kit, see part numbers 046-06B-KIT or 324-740 depending on your FJ40 production date. Your new SOR Silver Ceramic Header comes with a Kevlar Header Gasket but fresh new manifold stud hardware kit will help the job go smoothly, see part #044-02. |
SOR Silver Ceramic Coated Land Cruiser Headers
SOR Silver Ceramic Coated Headers

Silver Ceramic
Coated Headers
(click for large picture)

purchasing Stainless
Steel Braided Oil Lines
SOR 2 Piece Silver Ceramic Coated Headers are built exclusively for Specter Off-Road in the USA.These top quality headers are designed to fit right! Made from Ceramic Coated Steel to resist corrosion.
We installed these headers on a 2F engine in an FJ40 without emission controls and tested the vehicle on a chassis dynamometer. The difference between the stock Toyota exhaust and the SOR Silver Ceramic Coated Headers was a maximum increase of 16.6% in horsepower and 7.9% in torque. Your engine's performance change may be different.
Header specifications: Primary tubes are 1 5/16 inch inside diameter. The primary tube average length is 33 inches. The collectors are 2 1/16 inch inside diameter. The two piece Tri-Y design eliminates header warping, allows for frame flex and the slip fit exhaust connections eliminate exhaust flange gasket leaks. Header comes with band type clamps that do not deform the pipe. These clamps make for easy removal and replacement for engine or clutch service.

Fits 1969 to 12/78 FJ40 without emission controls. Can fit 1979 to 1984 FJ40 and 1980 to 1987 FJ60 vehicles without emission controls, by modifying header pipe to fit your vehicle's exhaust system Works with column shift linkage and floorshift models. Header will not fit with PTO Winch. Comes with Kevlar header gasket.
Requires SOR Stainless Steel Header Pipe for installation see part number #324-410.
SOR recommends purchasing Stainless Steel Braided Oil Lines. They’re longer than stock and provide better tolerance to excessive heat.
HEADERS ARE NOT LEGAL IN CALIFORNIA FOR USE ON VEHICLES EQUIPPED WITH POLLUTION CONTROLS. PLEASE CHECK YOUR LOCAL SMOG LAWS BEFORE INSTALLING HEADERS ON YOUR TOYOTA LAND CRUISER.
|
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
324-420 |
SOR SILVER CERAMIC COATED HEADERS -
Fits 1969-12/78 FJ40 without emission controls - Works with column shift linkage and floor shift models - Headers will not fit with PTO Winch - Will not fit FJ55 - Can also fit 1979 to 1984 FJ40 and 1980 to 1987 FJ60 vehicles without emission controls, by modifying header pipe to fit your vehicle's exhaust system - Comes with Kevlar header gasket and two Stainless Steel Band Clamps - REQUIRES Header Pipe for installation - See part 324-410. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 20.00 is already included in price) ![]() |
886.00 |
![]() |
![]() |
SOR Header Pipes are used to adapt the SOR 2 Piece Headers to the single stock exhaust system. SOR Header Pipes are designed to run above the skid plate for better protection and ground clearance.

Header pipe #324-410 will not fit on vehicles equipped with PTO winches, and cannot be shipped via parcel post.
|
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
324-410 |
SOR HEADER PIPE -
1968-1974 FJ40: SOR Header Pipe allows a bolt together connection to the factory muffler system. 1975 to 1978 FJ40 - Specter recommends updating the entire muffler and tail pipe assembly to a more free flowing system. Specter offers a complete bolt on system you can install in your own driveway at a fraction of a muffler shop's price, see 324-740. 1979 to 1987 FJ40 and FJ60 vehicles without emission controls will need to modify this header pipe and have the rear portion of the exhaust connected by an exhaust shop. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
165.25 |
![]() |
![]() |
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
1968-12/74 Muffler & Tail Pipe Kit |
---|---|---|---|---|---|---|
046-06B-KIT |
MUFFLER & TAIL PIPE KIT -
fits 1968-12/74 FJ40 - includes muffler, tail pipe, muffler mounting ring, tail pipe bracket, cushion, clamps for both ends of muffler and clamp for tail pipe bracket. ALSO fits 1958-1967 uses updated muffler & tailpipe -order #046-401, 405,404 hardware separately. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
312.25 |
![]() |
![]() |
||
1975-1978 Muffler & Tail Pipe Kit |
||||||
324-740 |
MUFFLER & TAIL PIPE KIT -
fits 1975-1978 FJ40 WITH SOR HEADERS - Includes muffler, tail pipe, muffler mounting ring, tail pipe bracket, cushion, both muffler clamps and the clamp for tail pipe bracket. This system routes exhaust above skid plate and exits behind the rear tire on the left side of the vehicle. Requires minor modification of skid plate. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
312.25 |
![]() |
![]() |
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
044-02B-KIT |
MANIFOLD STUD KIT -
1968-1974 F gas engine - Kit has qty 6 manifold studs, qty 6 manifold nuts, and qty 6 manifold washers. On Sale - Everyone gets the Discounted Price on this part. ![]() |
29.90 |
![]() |
![]() |
||
044-02C-KIT |
MANIFOLD STUD KIT -
1/75-8/87 2F gas engine - Kit has qty 6 manifold studs, qty 6 manifold nuts, qty 6 manifold washers, and 2 end bolts. On Sale - Everyone gets the Discounted Price on this part. ![]() |
44.00 |
![]() |
![]() |
||
044-02XB-KIT |
MANIFOLD STUD STEP–UP KIT -
Fits 12mm diameter at one end and 10mm at the other, 37mm long. Comes with nuts and washers for larger 12mm ends. Set of 6. Designed for early type head with later model manifolds. On Sale - Everyone gets the Discounted Price on this part. ![]() |
71.88 |
![]() |
![]() |
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
044-01B-SOR |
SOR GRAPHITE MANIFOLD GASKET -
Fits 1968-1974 F gas engine. This is a compressed graphite material with a stainless steel core. This unique gasket is about 1/8 inch thick and is designed to be compressed during installation. This compression helps seal manifolds that are not perfectly flat. Resists leaks due to warping. The stainless steel core resists blowing out. The graphite material is rated for temperatures in the 2000 degree range so the material will not deteriorate due to exhaust heat. Mfg suggested fastener torque of 20-25 ft lb. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
71.25 |
![]() |
![]() |
||
044-01B-PAIR |
PAIR SOR GRAPHITE MANIFOLD GASKET SET -
Fits 1968-1974 F gas engine. SAVE $$ when you buy 2 gaskets. This is a compressed graphite material with a stainless steel core. This unique gasket is about 1/8 inch thick and is designed to be compressed during installation. This compression helps seal manifolds that are not perfectly flat. Resists leaks due to warping. The stainless steel core resists blowing out. The graphite material is rated for temperatures in the 2000 degree range so the material will not deteriorate due to exhaust heat. Mfg suggested fastener torque of 20-25 ft lb. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
96.25 |
![]() |
![]() |
||
044-01C-SOR |
SOR GRAPHITE MANIFOLD GASKET -
Fits 1/75-8/87 2F gas engine. This is a compressed graphite material with a stainless steel core. This unique gasket is about 1/8 inch thick and is designed to be compressed during installation. This compression helps seal manifolds that are not perfectly flat. Resists leaks due to warping. The stainless steel core resists blowing out. The graphite material is rated for temperatures in the 2000 degree range so the material will not deteriorate due to exhaust heat. Mfg suggested fastener torque of 20-25 ft lb. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
71.25 |
![]() |
![]() |
||
044-01C-PAIR |
PAIR SOR GRAPHITE MANIFOLD GASKET SET -
Fits 1975-1987 2F gas engine. SAVE $$ when you buy 2 gaskets. This is a compressed graphite material with a stainless steel core. This unique gasket is about 1/8 inch thick and is designed to be compressed during installation. This compression helps seal manifolds that are not perfectly flat. Resists leaks due to warping. The stainless steel core resists blowing out. The graphite material is rated for temperatures in the 2000 degree range so the material will not deteriorate due to exhaust heat. Mfg suggested fastener torque of 20-25 ft lb. On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
96.25 |
![]() |
![]() |
SOR Kevlar Header Gaskets are specially made to be heat resistant. Long lasting to withstand temperatures up to 750 degrees Fahrenheit. Say good-bye to Asbestos header gaskets.
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
324-715 |
KEVLAR HEADER GASKET -
Fits 1968-8/87 Club Price with 15% Discount is $ 13.39 Click here for info about joining Club SOR ![]() |
15.75 |
![]() |
![]() |
Stock shaped manifold gaskets can also be used for your new SOR Silver Ceramic Coated Headers
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
044-01B |
AFTERMARKET MANIFOLD GASKET -
Fits 1968-1974 F gas engine On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
39.75 |
![]() |
![]() |
||
044-01C |
MANIFOLD GASKET -
Fits 1/75-8/87 2F gas engine On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
57.99 |
![]() |
![]() |
Buy |
Quantity |
Part Number |
Description
|
Price |
In Stock |
Picture Click
to Enlarge |
---|---|---|---|---|---|---|
046-06B |
OEM MUFFLER -
Fits 1968-1974 FJ40 On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
122.57 |
![]() |
![]() |
||
046-07B |
FJ40 TAIL PIPE-
Fits 1968-12/74 FJ40-Has a 1 7/8 inch opening at muffler end On Sale - Everyone gets the Discounted Price on this part. (an Additional Handling Charge of 16.25 is already included in price) ![]() |
95.25 |
![]() |
![]() |
||
046-08B |
AFTERMARKET MUFFLER RING -
Fits 1967-1974 FJ40 On Sale - Everyone gets the Discounted Price on this part. ![]() |
28.00 |
![]() |
![]() |
||
046-09A-A |
AFTERMARKET MUFFLER RING PAD-
Fits 1958-12/74 FJ40 Club Price with 15% Discount is $ 2.27 Click here for info about joining Club SOR ![]() |
2.67 |
![]() |
![]() |
||
046-09B |
MUFFLER RING PAD -
Fits 1968-12/74 FJ55 On Sale - Everyone gets the Discounted Price on this part. ![]() |
8.42 |
![]() |
![]() |
||
046-11B-A |
AFTERMARKET TAILPIPE BRACKET -
1968-12/74 FJ40 On Sale - Everyone gets the Discounted Price on this part. ![]() |
44.00 |
![]() |
![]() |
||
046-12 |
SMALL MUFFLER CLAMP -
Fits 2 inch pipe Club Price with 15% Discount is $ 5.74 Click here for info about joining Club SOR ![]() |
6.75 |
![]() |
![]() |
||
046-13 |
LARGE MUFFLER CLAMP -
Fits 2-1/4 inch pipe On Sale - Everyone gets the Discounted Price on this part. ![]() |
6.15 |
![]() |
![]() |
||
046-23B-SS |
REPLACEMENT STAINLESS STEEL BAND CLAMP -
Stainless Steel clamps - Size 57.2 MM - sold each On Sale - Everyone gets the Discounted Price on this part. ![]() |
10.00 |
![]() |
![]() |